mirror of
https://github.com/mechano/Kingroon_KP3S_Marlin_Firmware.git
synced 2025-12-03 03:46:24 +04:00
Add files via upload
This commit is contained in:
Roberto Giuffre`
117
Configuration.h
117
Configuration.h
@@ -20,8 +20,8 @@
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
#define CONFIG_EXAMPLES_DIR "Kingroon/KP3S"
|
||||
//#error "Don't build with import-2.1.x configurations!"
|
||||
//#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
@@ -63,7 +63,7 @@
|
||||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "Mechano" // Who made the changes.
|
||||
#define STRING_CONFIG_H_AUTHOR "(kubik369)" // Who made the changes.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
// @section machine
|
||||
@@ -94,7 +94,7 @@
|
||||
*
|
||||
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
|
||||
*/
|
||||
#define BAUDRATE 115200 // GR lower speed serial was 250000
|
||||
#define BAUDRATE 250000
|
||||
|
||||
//#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate
|
||||
|
||||
@@ -150,9 +150,9 @@
|
||||
* TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
|
||||
* :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE A4988
|
||||
#define Y_DRIVER_TYPE A4988
|
||||
#define Z_DRIVER_TYPE A4988
|
||||
#define X_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Y_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z_DRIVER_TYPE TMC2208_STANDALONE
|
||||
//#define X2_DRIVER_TYPE A4988
|
||||
//#define Y2_DRIVER_TYPE A4988
|
||||
//#define Z2_DRIVER_TYPE A4988
|
||||
@@ -164,7 +164,7 @@
|
||||
//#define U_DRIVER_TYPE A4988
|
||||
//#define V_DRIVER_TYPE A4988
|
||||
//#define W_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE TMC2208_STANDALONE
|
||||
//#define E1_DRIVER_TYPE A4988
|
||||
//#define E2_DRIVER_TYPE A4988
|
||||
//#define E3_DRIVER_TYPE A4988
|
||||
@@ -639,7 +639,7 @@
|
||||
// Above this temperature the heater will be switched off.
|
||||
// This can protect components from overheating, but NOT from shorts and failures.
|
||||
// (Use MINTEMP for thermistor short/failure protection.)
|
||||
#define HEATER_0_MAXTEMP 305 // GR reaching 300°C
|
||||
#define HEATER_0_MAXTEMP 305 // GR raggiungiamo i 300 gradi
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
@@ -647,7 +647,7 @@
|
||||
#define HEATER_5_MAXTEMP 275
|
||||
#define HEATER_6_MAXTEMP 275
|
||||
#define HEATER_7_MAXTEMP 275
|
||||
#define BED_MAXTEMP 120 // GR bed at 110°C see overshot
|
||||
#define BED_MAXTEMP 120 // GR raggiungiamo i 300 gradi
|
||||
#define CHAMBER_MAXTEMP 60
|
||||
|
||||
/**
|
||||
@@ -656,8 +656,8 @@
|
||||
* (especially before PID tuning). Setting the target temperature too close to MAXTEMP guarantees
|
||||
* a MAXTEMP shutdown! Use these values to forbid temperatures being set too close to MAXTEMP.
|
||||
*/
|
||||
#define HOTEND_OVERSHOOT 5 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT // Necessary for 300°C was 15
|
||||
#define BED_OVERSHOOT 10 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
|
||||
#define HOTEND_OVERSHOOT 5 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT // GR necessario per i 300 gradi
|
||||
#define BED_OVERSHOOT 10 // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT // GR necessario per i 110 gradi
|
||||
#define COOLER_OVERSHOOT 2 // (°C) Forbid temperatures closer than OVERSHOOT
|
||||
|
||||
//===========================================================================
|
||||
@@ -691,9 +691,9 @@
|
||||
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
|
||||
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
|
||||
#else
|
||||
#define DEFAULT_Kp 22.20
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114.00
|
||||
#define DEFAULT_Kp 12.93 // GR rilevati con Pronterface sulla mia stampante
|
||||
#define DEFAULT_Ki 0.78 // GR rilevati con Pronterface sulla mia stampante
|
||||
#define DEFAULT_Kd 53.51 // GR rilevati con Pronterface sulla mia stampante
|
||||
#endif
|
||||
#else
|
||||
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
|
||||
@@ -844,8 +844,8 @@
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash) // GR edit menu for PID
|
||||
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash) // GR PID autotune menu
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash) // GR Un menu per editare PID a mano
|
||||
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash) // GR Un menu per PID autotune
|
||||
#endif
|
||||
|
||||
// @section safety
|
||||
@@ -1175,8 +1175,13 @@
|
||||
#define X_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Y_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#ifdef USE_BLTOUCH
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE LOW
|
||||
#else
|
||||
#define Z_MIN_ENDSTOP_HIT_STATE LOW
|
||||
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#endif
|
||||
#define I_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
#define I_MAX_ENDSTOP_HIT_STATE HIGH
|
||||
#define J_MIN_ENDSTOP_HIT_STATE HIGH
|
||||
@@ -1310,7 +1315,7 @@
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define DEFAULT_EJERK 15.0 // May be used by Linear Advance
|
||||
#define DEFAULT_EJERK 15.0 // May be used by Linear Advance // GR era 5 Linear Advance vuole almeno 10
|
||||
|
||||
/**
|
||||
* Junction Deviation Factor
|
||||
@@ -1349,10 +1354,11 @@
|
||||
* The probe replaces the Z-MIN endstop and is used for Z homing.
|
||||
* (Automatically enables USE_PROBE_FOR_Z_HOMING.)
|
||||
*/
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
// Force the use of the probe for Z-axis homing
|
||||
//#define USE_PROBE_FOR_Z_HOMING
|
||||
#ifdef USE_BLTOUCH
|
||||
#define USE_PROBE_FOR_Z_HOMING
|
||||
#else
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_PIN
|
||||
@@ -1367,7 +1373,9 @@
|
||||
* - Normally-closed (NC) also connect to GND.
|
||||
* - Normally-open (NO) also connect to 5V.
|
||||
*/
|
||||
//#define Z_MIN_PROBE_PIN -1
|
||||
#ifdef USE_BLTOUCH
|
||||
#define Z_MIN_PROBE_PIN Z_MAX_PIN
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Probe Type
|
||||
@@ -1409,7 +1417,9 @@
|
||||
/**
|
||||
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
|
||||
*/
|
||||
//#define BLTOUCH
|
||||
#ifdef USE_BLTOUCH
|
||||
#define BLTOUCH
|
||||
#endif
|
||||
|
||||
/**
|
||||
* MagLev V4 probe by MDD
|
||||
@@ -1570,7 +1580,7 @@
|
||||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 30.0, -1.0, -2.605 }
|
||||
#define NOZZLE_TO_PROBE_OFFSET { X_PROBE_OFFSET, Y_PROBE_OFFSET, Z_PROBE_OFFSET }
|
||||
|
||||
// Enable and set to use a specific tool for probing. Disable to allow any tool.
|
||||
#define PROBING_TOOL 0
|
||||
@@ -1807,8 +1817,8 @@
|
||||
// @section geometry
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 180 // GR was 165
|
||||
#define Y_BED_SIZE 180 // GR was 170
|
||||
#define X_BED_SIZE 172
|
||||
#define Y_BED_SIZE 172
|
||||
|
||||
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS -10
|
||||
@@ -1884,9 +1894,9 @@
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT false // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
|
||||
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
|
||||
@@ -2027,9 +2037,12 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
#ifdef USE_BLTOUCH
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
#else
|
||||
#define MESH_BED_LEVELING
|
||||
#endif
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Commands to execute at the end of G29 probing.
|
||||
@@ -2048,10 +2061,10 @@
|
||||
/**
|
||||
* Auto-leveling needs preheating
|
||||
*/
|
||||
#define PREHEAT_BEFORE_LEVELING
|
||||
// #define PREHEAT_BEFORE_LEVELING // GR commento nessun preriscaldamento prima del livellamento
|
||||
#if ENABLED(PREHEAT_BEFORE_LEVELING)
|
||||
#define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
|
||||
#define LEVELING_BED_TEMP 50
|
||||
#define LEVELING_NOZZLE_TEMP 210 // (°C) Only applies to E0 at this time // GR era 120
|
||||
#define LEVELING_BED_TEMP 60 // GR era 50
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -2185,7 +2198,7 @@
|
||||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 4 // Don't use more than 7 points per axis, implementation limited. // GR 4x4 16 point manual leveling
|
||||
#define GRID_MAX_POINTS_X 4 // Don't use more than 7 points per axis, implementation limited. // GR 4 punti di calibrazione manuale
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
@@ -2201,7 +2214,7 @@
|
||||
#if ENABLED(LCD_BED_LEVELING)
|
||||
#define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
|
||||
#define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||||
//#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#endif
|
||||
|
||||
// Add a menu item to move between bed corners for manual bed adjustment
|
||||
@@ -2263,11 +2276,13 @@
|
||||
* - Allows Z homing only when XY positions are known and trusted.
|
||||
* - If stepper drivers sleep, XY homing may be required again before Z homing.
|
||||
*/
|
||||
//#define Z_SAFE_HOMING
|
||||
#ifdef USE_BLTOUCH
|
||||
#define Z_SAFE_HOMING
|
||||
#endif
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing
|
||||
#define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
|
||||
#define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
|
||||
//#define Z_SAFE_HOMING_POINT_ABSOLUTE // Ignore home offsets (M206) for Z homing position
|
||||
#endif
|
||||
|
||||
@@ -2356,7 +2371,7 @@
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build. // GR init EEPROM on first boot of new firmware
|
||||
#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
|
||||
#endif
|
||||
|
||||
// @section host
|
||||
@@ -2389,14 +2404,14 @@
|
||||
// Preheat Constants - Up to 10 are supported without changes
|
||||
//
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 210 // GR better value for PLA
|
||||
#define PREHEAT_1_TEMP_HOTEND 210
|
||||
#define PREHEAT_1_TEMP_BED 60
|
||||
#define PREHEAT_1_TEMP_CHAMBER 35
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "PETG"
|
||||
#define PREHEAT_2_TEMP_HOTEND 235 // GR better value for PETG
|
||||
#define PREHEAT_2_TEMP_BED 75
|
||||
#define PREHEAT_2_TEMP_HOTEND 235
|
||||
#define PREHEAT_2_TEMP_BED 80
|
||||
#define PREHEAT_2_TEMP_CHAMBER 35
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
@@ -3414,13 +3429,13 @@
|
||||
//#define DISABLE_ENCODER // Disable the click encoder, if any
|
||||
//#define TOUCH_IDLE_SLEEP_MINS 5 // (minutes) Display Sleep after a period of inactivity. Set with M255 S.
|
||||
|
||||
#define TOUCH_SCREEN_CALIBRATION
|
||||
#define TOUCH_SCREEN_CALIBRATION
|
||||
|
||||
//#define TOUCH_CALIBRATION_X -11758 // GR calibrate at first boot
|
||||
//#define TOUCH_CALIBRATION_Y 8553
|
||||
//#define TOUCH_OFFSET_X 353
|
||||
//#define TOUCH_OFFSET_Y -16
|
||||
//#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
|
||||
//#define TOUCH_CALIBRATION_X -11758 // GR deve chiedere la calibrazione
|
||||
//#define TOUCH_CALIBRATION_Y 8553 // GR deve chiedere la calibrazione
|
||||
//#define TOUCH_OFFSET_X 353 // GR deve chiedere la calibrazione
|
||||
//#define TOUCH_OFFSET_Y -16 // GR deve chiedere la calibrazione
|
||||
//#define TOUCH_ORIENTATION TOUCH_LANDSCAPE // GR deve chiedere la calibrazione
|
||||
|
||||
#if ALL(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
|
||||
#define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
|
||||
|
||||
Reference in New Issue
Block a user