### If your system is not added here that doesn't mean flipper don't support it! Look into add manually menu, and search for your manufacturers inscturctions!
### Also many supported systems can be used only from `Read` mode, `Add Manually` is used only to make new remotes that can be binded with receiver
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> FAAC SLH (select your frequency)
2. Open your new remote file
3. Open your receiver box, find programming button on the receiver board.
4. Hold Up arrow button on the flipper to send programming signal - at same time press and hold programming button on the receiver board.
5. Led on the receiver board will light on, then off, then on, then off again then on again
6. Release all buttons
7. Press send button on the flipper couple times holding it for 1-3 seconds
8. Done!
Watch this video to learn more : https://www.youtube.com/watch?v=NfZmMy37XUs
...
How to get Seed value from your original remote or bind new remote using existing (master) remote?
1. Go to SubGHz -> Read - Select frequency 868.35 or 433.92 and modulation AM650
2. Hold two buttons on the original master remote until led turns on
3. Click one button that you want to get seed from (Seed is unique for each button on original remote!)
4. You will get signal in the read screen on flipper, open that and see your original remote seed for button you used
5. You can create new remote using that seed and bind that to receiver without opening the box! Faac has procedure that allows to bind new remotes using master remote, you can use flipper for that
6. Go to SubGHz -> Add Manually -> FAAC SLH Man. (your Freq)
7. Enter those values -> REPLACE `R` with any random digits like 1,2,3..
FIX -> A0 RR RR R6
COUNTER -> 00 00 02
SEED -> Your seed from the remote button you got earlier
8. Flipper will act as new remote, press Send button couple times near the receiver to register new remote
**This instruction for older boards, if your has no** `Learn`**button but has buttons**`F`, `CL`, `+`, `-`**read instruction from Alutech AT4N**
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> AN-Motors AT4 433Mhz
2. Open your new remote file
3. Open your receiver box, find button `Learn` click it one time, led will turn on.
4. Press `Send` on your flipper one time, led on receiver board will turn off.
5. Press `Send` on your flipper again, led on receiver will start flashing, wait couple seconds until led turns off.
6. Done
Watch this video to learn more (video in Russian language): https://www.youtube.com/watch?v=URVMtTELcnU
## Alutech AT4N (AN-Motors)
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> Alutech AT4N 433Mhz
2. Open your new remote file
3. Open your receiver box, find button `F` press it for ~3sec, display will show `Pr`.
4. Click `F` button couple times until you see `Lr` on screen
5. Using buttons `+` / `-` select free number that has no remotes in it (if it has remote programmed on that number, it will show a red dot on the down right corner)
6. Press `Send` on your flipper one time, display on receiver board will flash and red dot will appear next to remote number.
7. Press button `F` on receiver board for ~3sec to exit programming mode
8. Done
Watch this video to learn more and see how different boards can be programmed (video in Russian language): https://www.youtube.com/watch?v=XrOVVYhFXDg
## Aprimatic TR
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> KL: Aprimatic 433Mhz
2. Open your new remote file
3. Push all 4 buttons at same time on your existing remote thats already works with receiver
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> KL: Doorhan 433Mhz or 315Mhz depends on your receiver (find out by reading your existing remote)
2. Open your new remote file
3. Push `P` button for ~2 sec, led will start flashing
4. Press `Send` on your flipper for ~2 seconds
5. Led on the receiver board will flash and turn off
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> KL: Doorhan 433Mhz or 315Mhz depends on your receiver (find out by reading your existing remote)
2. Open your new remote file
3. For next steps be close to the receiver board, around 1-2 meters
4. Press second button (lowest one) on the old remote, do not release second button and press 1st (upper) button, hold buttons for 1 sec and release them
5. Press working button on the old remote (the button you use for operating the receiver, aka opening the gate, etc) hold for 1 sec and release
6. Actions with old remote must be done in 5 seconds time, do not hold buttons for too long, and do not make it very fast
7. Receiver will beep, you will have 10 seconds to add new remote, now press Send on new remote on flipper two times holding for at least 1 sec
8. Receiver will beep again telling that new remote is added sucessfuly!
9. Done!
With copy of existing remote on flipper:
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> KL: Doorhan 433Mhz or 315Mhz depends on your receiver (find out by reading your existing remote)
2. Open your existing remote (original) file
3. For next steps be close to the receiver board, around 1-2 meters
4. Press left button (0x8) on the flipper, hold for 1 sec and release the button and press right (0xA) button, hold button for 1 sec and release
5. Press working button on the flipper, should be center one aka Send (the button you use for operating the receiver, aka opening the gate, etc) hold for 1 sec and release
6. Actions with original remote copy must be done in 5 seconds time, do not hold buttons for too long, and do not make it very fast
7. Receiver will beep, now hold back and open new remote file, you will have 10 seconds to add new remote, press Send on new remote on flipper two times holding for at least 1 sec
8. Receiver will beep again telling that new remote is added sucessfuly!
Watch this videos to learn more (videos in Russian language): https://www.youtube.com/watch?v=wZ5121HYv50 / https://www.youtube.com/watch?v=1ucrDKF3vWc
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> BFT Mitto 433Mhz
2. Open your new remote file
3. Open your receiver board box
4.**Watch this video**: https://www.youtube.com/watch?v=5QXMBKI_-Ls
5. Long press (Right Arrow) - (0xF button - Btn:F) on Flipper for like 3-5 sec -> Will act like holding Button 1 & 2 on original remote as shown on video
6. Done?
--
How to get seed to make full clone of your remote (**will conflict with original remote!!!!!**):
**WARNING!!!! This method can desync your original remote, please avoid using it! It can be used in rare cases like when your remote works poorly or has broken buttons and you want to replace it with flipper**
1. Open `Read` in SubGHz on your flipper
2. (ONLY FOR ORIGINAL REMOTES) Hold all buttons on your remote at same time, example -> for 2 button remote - press them both at same time and hold OR press hidden button on back of remote with a pin or paper clip
4. If `Fix:` is showing first `F` see `Hop:` value -> This is your remote Seed (except first digit `F` (this is the button code, aka programming button pressed means `F`))
5. Write down Hop value and replace first digit - `F` with `0`
6. Press button on your remote that you want to clone and receive its signal on your flipper
7. Open and write down `Fix:` value where first digit will be same as your button ID `Btn:`
8. Create new remote using BFT Mitto [Manual] - Enter FIX from step 7, enter counter `FF F9`, enter seed from step 5
9. Using counter values like `FF F9` can help bypassing current original remote counter value, and in result it also can fully desync original remote, only one remote can work at same time using this method
10. Also you can do this: Save your signal of the original remote (will say KL: Unknown),
then copy file to the PC and edit it and insert/replace those values after the `Key: 01 23 45 67 89 AB CD EF` (your key will have different value)
```
Seed: 0X XX XX XX
Manufacture: BFT
```
Replace `X`'s with digits from your Seed that you obtained by reading two button hold at the first steps,
Save and copy that file back to the flipper
Now you will have exact clone of your remote that will have same counter, by making couple presses you will make it higher than original and receiver will work with it, but original remote will reguire same amount of presses to work again, and vice versa.
11. Also your original remote may become non working since it needs to be re-added into receiver board if you made counter much higher than original :C
