mirror of
https://github.com/OneOfEleven/uv-k5-firmware-custom.git
synced 2025-06-19 14:48:03 +03:00
Fixed F+4 and F+* freq/ctcss/cdcss search functions
This commit is contained in:
OneOfEleven
81
README.md
81
README.md
@ -34,47 +34,46 @@ us to remove certain firmware features in order to make room in the flash for ot
|
||||
You'll find the options at the top of "Makefile" ('0' = disable, '1' = enable) ..
|
||||
|
||||
```
|
||||
ENABLE_CLANG := 0 **experimental, builds with clang instead of gcc (LTO will be disabled if you enable this)
|
||||
ENABLE_SWD := 0 only needed if using CPU's SWD port (debugging/programming)
|
||||
ENABLE_OVERLAY := 0 cpu FLASH stuff, not needed
|
||||
ENABLE_LTO := 0 **experimental, reduces size of compiled firmware but might break EEPROM reads (OVERLAY will be disabled if you enable this)
|
||||
ENABLE_UART := 1 without this you can't configure radio via PC
|
||||
ENABLE_UART_DEBUG := 0 just for code debugging, it sends debug info along the USB serial connection (programming lead)
|
||||
ENABLE_AIRCOPY := 1 clone radio-to-radio via RF
|
||||
ENABLE_AIRCOPY_FREQ := 1 remember what you use for the aircopy frequency
|
||||
ENABLE_FMRADIO := 1 WBFM VHF broadcast band receiver
|
||||
ENABLE_NOAA := 1 everything NOAA (only of any use in the USA)
|
||||
ENABLE_VOICE := 0 want to hear voices ?
|
||||
ENABLE_MUTE_RADIO_FOR_VOICE := 1 mute the radios audio when a voice is playing
|
||||
ENABLE_VOX := 1 voice operated transmission
|
||||
ENABLE_ALARM := 1 TX alarms
|
||||
ENABLE_1750HZ := 1 side key 1750Hz TX tone (older style repeater access)
|
||||
ENABLE_PWRON_PASSWORD := 0 '1' = allow power-on password
|
||||
ENABLE_RESET_AES_KEY := 1 '1' = reset/clear the AES key stored in the eeprom
|
||||
ENABLE_BIG_FREQ := 0 big font frequencies (like original QS firmware)
|
||||
ENABLE_SMALL_BOLD := 1 bold channel name/no. (when name + freq channel display mode)
|
||||
ENABLE_KEEP_MEM_NAME := 1 maintain channel name when (re)saving memory channel
|
||||
ENABLE_WIDE_RX := 1 full 18MHz to 1300MHz RX (though front-end/PA not designed for full range)
|
||||
ENABLE_1250HZ_STEP := 1 enable smaller 1.25kHz frequency steps
|
||||
ENABLE_TX_WHEN_AM := 0 allow TX (always FM) when RX is set to AM
|
||||
ENABLE_F_CAL_MENU := 0 enable/disable the radios hidden frequency calibration menu
|
||||
ENABLE_CTCSS_TAIL_PHASE_SHIFT := 1 standard CTCSS tail phase shift rather than QS's own 55Hz tone method
|
||||
ENABLE_BOOT_BEEPS := 0 gives user audio feedback on volume knob position at boot-up
|
||||
ENABLE_SHOW_CHARGE_LEVEL := 0 show the charge level when the radio is on charge
|
||||
ENABLE_REVERSE_BAT_SYMBOL := 1 mirror the battery symbol on the status bar (+ pole on the right)
|
||||
ENABLE_CODE_SCAN_TIMEOUT := 0 timeout if CTCSS/CDCSS is not found
|
||||
ENABLE_FREQ_CODE_SCAN_TIMEOUT := 1 timeout if CTCSS/CDCSS is not found after a successful frequency scan
|
||||
ENABLE_FREQ_CODE_ROUNDING := 0 rounds the detected RF frequency to the nearest step size in use - F+4 scan mode
|
||||
ENABLE_AM_FIX := 1 dynamically adjust the front end gains when in AM mode to helo prevent AM demodulator saturation, ignore the on-screen RSSI level (for now)
|
||||
ENABLE_AM_FIX_SHOW_DATA := 1 show debug data for the AM fix (still tweaking it)
|
||||
ENABLE_SQUELCH_MORE_SENSITIVE := 1 make squelch levels a little bit more sensitive - I plan to let user adjust the values themselves
|
||||
ENABLE_FASTER_CHANNEL_SCAN := 1 increases the channel scan speed, but the squelch is also made more twitchy
|
||||
ENABLE_RSSI_BAR := 1 enable a dBm/Sn RSSI bar graph level inplace of the little antenna symbols
|
||||
ENABLE_SHOW_TX_TIMEOUT := 0 show the remainng TX time
|
||||
ENABLE_AUDIO_BAR := 1 experimental, display an audo bar level when TX'ing, includes remaining TX time (in seconds)
|
||||
ENABLE_COPY_CHAN_TO_VFO := 1 copy current channel into the other VFO. Long press Menu key ('M')
|
||||
#ENABLE_BAND_SCOPE := 0 not yet implemented - spectrum/pan-adapter
|
||||
#ENABLE_SINGLE_VFO_CHAN := 0 not yet implemented - single VFO on display when possible
|
||||
ENABLE_CLANG := 0 **experimental, builds with clang instead of gcc (LTO will be disabled if you enable this)
|
||||
ENABLE_SWD := 0 only needed if using CPU's SWD port (debugging/programming)
|
||||
ENABLE_OVERLAY := 0 cpu FLASH stuff, not needed
|
||||
ENABLE_LTO := 0 **experimental, reduces size of compiled firmware but might break EEPROM reads (OVERLAY will be disabled if you enable this)
|
||||
ENABLE_UART := 1 without this you can't configure radio via PC
|
||||
ENABLE_UART_DEBUG := 0 just for code debugging, it sends debug info along the USB serial connection (programming lead)
|
||||
ENABLE_AIRCOPY := 1 clone radio-to-radio via RF
|
||||
ENABLE_AIRCOPY_FREQ := 1 remember what you use for the aircopy frequency
|
||||
ENABLE_FMRADIO := 1 WBFM VHF broadcast band receiver
|
||||
ENABLE_NOAA := 1 everything NOAA (only of any use in the USA)
|
||||
ENABLE_VOICE := 0 want to hear voices ?
|
||||
ENABLE_MUTE_RADIO_FOR_VOICE := 1 mute the radios audio when a voice is playing
|
||||
ENABLE_VOX := 1 voice operated transmission
|
||||
ENABLE_ALARM := 1 TX alarms
|
||||
ENABLE_1750HZ := 1 side key 1750Hz TX tone (older style repeater access)
|
||||
ENABLE_PWRON_PASSWORD := 0 '1' = allow power-on password
|
||||
ENABLE_RESET_AES_KEY := 1 '1' = reset/clear the AES key stored in the eeprom (only if it's set)
|
||||
ENABLE_BIG_FREQ := 0 big font frequencies (like original QS firmware)
|
||||
ENABLE_SMALL_BOLD := 1 bold channel name/no. (when name + freq channel display mode)
|
||||
ENABLE_KEEP_MEM_NAME := 1 maintain channel name when (re)saving memory channel
|
||||
ENABLE_WIDE_RX := 1 full 18MHz to 1300MHz RX (though front-end/PA not designed for full range)
|
||||
ENABLE_1250HZ_STEP := 1 enable smaller 1.25kHz frequency steps
|
||||
ENABLE_TX_WHEN_AM := 0 allow TX (always FM) when RX is set to AM
|
||||
ENABLE_F_CAL_MENU := 0 enable/disable the radios hidden frequency calibration menu
|
||||
ENABLE_CTCSS_TAIL_PHASE_SHIFT := 1 standard CTCSS tail phase shift rather than QS's own 55Hz tone method
|
||||
ENABLE_BOOT_BEEPS := 0 gives user audio feedback on volume knob position at boot-up
|
||||
ENABLE_SHOW_CHARGE_LEVEL := 0 show the charge level when the radio is on charge
|
||||
ENABLE_REVERSE_BAT_SYMBOL := 1 mirror the battery symbol on the status bar (+ pole on the right)
|
||||
ENABLE_FREQ_SEARCH_TIMEOUT := 1 timeout if FREQ not found
|
||||
ENABLE_CODE_SEARCH_TIMEOUT := 0 timeout if CTCSS/CDCSS not found
|
||||
ENABLE_AM_FIX := 1 dynamically adjust the front end gains when in AM mode to helo prevent AM demodulator saturation, ignore the on-screen RSSI level (for now)
|
||||
ENABLE_AM_FIX_SHOW_DATA := 1 show debug data for the AM fix (still tweaking it)
|
||||
ENABLE_SQUELCH_MORE_SENSITIVE := 1 make squelch levels a little bit more sensitive - I plan to let user adjust the values themselves
|
||||
ENABLE_FASTER_CHANNEL_SCAN := 1 increases the channel scan speed, but the squelch is also made more twitchy
|
||||
ENABLE_RSSI_BAR := 1 enable a dBm/Sn RSSI bar graph level inplace of the little antenna symbols
|
||||
ENABLE_SHOW_TX_TIMEOUT := 0 show the remainng TX time
|
||||
ENABLE_AUDIO_BAR := 1 experimental, display an audo bar level when TX'ing, includes remaining TX time (in seconds)
|
||||
ENABLE_COPY_CHAN_TO_VFO := 1 copy current channel into the other VFO. Long press Menu key ('M')
|
||||
#ENABLE_BAND_SCOPE := 0 not yet implemented - spectrum/pan-adapter
|
||||
#ENABLE_SINGLE_VFO_CHAN := 0 not yet implemented - single VFO on display when possible
|
||||
```
|
||||
|
||||
# New/modified function keys
|
||||
|
||||
Reference in New Issue
Block a user