* Initial support for n810

- Fix set_altinterface workaround which seems to be checked by nolo 1.7
- n810 has the same USBID than n770
* Define some nolo commands used in query.c in nolo.h
* Get SW version with -i too

Makefile

@@ -1,3 +1,4 @@
+include config.mk
 PREFIX?=/usr/local
 
 all: logot

config.mk

@@ -0,0 +1,8 @@
+VERSION=0.3.2
+PREFIX=/usr
+
+# NetBSD stuff
+CFLAGS+=-I/usr/pkg/include
+LDFLAGS+=-L/usr/pkg/lib -Wl,-R/usr/pkg/lib
+
+HAVE_USB=1

doc/fiasco

@@ -0,0 +1,30 @@
+SPECS FOR TEH FIASCO FIRMWARE FILE FORMAT ffff!
+-----------------------------------------------
+
+  These notes has not been taken properly and may be wrong. It must
+  be revised to fit the reality. But this is mostly a general idea:
+
+
+FILE HEADER
+
+   1 byte = 0xb4    --  signature
+   4 bytes          --  firmware name length (big endian)
+   6 bytes          --  versioning info ( byte 4 is format version )
+   N-6 bytes        --  firmware name (zero fill)
+
+
+PIECE HEADER
+
+   1 byte = 0x54    --  piece signature
+   6 bytes          --  unknown
+   2 bytes          --  checksum for the piece contents (xorpair)
+  12 bytes          --  piece name (first byte is FF if is the last)
+   4 bytes          --  piece size (big endian)
+   4 bytes          --  unknown
+             block {
+   1 byte           --  if (value '1'-'9') { ..there's a comment.. }
+   1 byte           --  length of comment
+   N bytes          --  comment
+             }
+   N bytes          -- piece data
+  

doc/usage

@@ -8,6 +8,7 @@ Tablets (n770 and n800).
   - reboot de mother board
   - extract the current firmware pieces from the device (dump)
   - set the USB host/slave mode
+  - pack/unpack fiasco firmwares
   - fine grained R&D flags support
   - identify firmware pieces
   - dump mtd partitions (embedded mtd-utils source code)
@@ -19,27 +20,29 @@ Tablets (n770 and n800).
 This is the help message of the tool:
 <pre>
 <b>~$ 0xFFFF -h</b>
-0xFFFF v0.2  // The Free Fiasco Firmware Flasher
+0xFFFF v0.3  // The Free Fiasco Firmware Flasher
  -b [arg]       boots the kernel with arguments
- -e [path]      dump and extract pieces to path
- -r [0|1]       disable/enable R&D mode
- -f <flags>     set the given RD flags (see '-f help')
- -p [[p%]file]  piece-of-firmware % file-where-this-piece-is
- -u [fiasco]    unpack target fiasco image
- -U [0|1]       disable/enable the usb host mode
- -s [serial]    serial port console (minicom like terminal)
- -C [/dev/mtd]  check bad blocks on mtd
  -c             console prompt mode
- -h             show this help message
+ -C [/dev/mtd]  check bad blocks on mtd
- -i             show device information (let standby mode)
- -I [piece]     identify a firmware piece
- -l             list supported usb device ids
  -d [vid:pid]   injects a usb device into the supported list
  -D [0|1|2]     sets the root device to flash (0), mmc (1) or usb (2)
+ -e [path]      dump and extract pieces to path
+ -f <flags>     set the given RD flags (see '-f help')
+ -F [fiasco]    flash a fiasco firmware image
+ -h             show this help message
+ -H [file]      calculate hash for file
+ -i             show device information (let standby mode)
+ -I [piece]     identify a firmware piece
+ -l, -L         list supported usb device ids
+ -p [[p%]file]  piece-of-firmware % file-where-this-piece-is
+ -r [0|1]       disable/enable R&D mode
  -R             reboot the omap board
- -x             extract configuration entries from /dev/mtd1
+ -s [serial]    serial port console (minicom like terminal)
+ -u [fiasco]    unpack target fiasco image
+ -U [0|1]       disable/enable the usb host mode
  -v             be verbose and noisy
  -V             show 0xFFFF version information
+ -x             extract configuration entries from /dev/mtd1
 Pieces are: xloader secondary kernel initfs rootfs omap-nand 
 </pre>
 

gui/Makefile

@@ -1,8 +1,11 @@
 OBJ=main.o
 BIN=goxf
 
-CFLAGS=`pkg-config gladeui-1.0 libglade-2.0 --cflags`
+CFLAGS=`pkg-config gladeui-1.0 libglade-2.0 gmodule-2.0 --cflags`
-LDFLAGS=`pkg-config gladeui-1.0 libglade-2.0 --libs`
+LDFLAGS=`pkg-config gladeui-1.0 libglade-2.0 gmodule-2.0 --libs`
 
 all: ${OBJ}
 	${CC} ${LDFLAGS} ${OBJ} -o ${BIN}
+
+clean:
+	-rm -f ${BIN} ${OBJ}

gui/g0xFFFF.glade

@@ -21,7 +21,7 @@
               <widget class="GtkComboBox" id="combobox2">
                 <property name="visible">True</property>
                 <property name="active">0</property>
-                <property name="items" translatable="yes" context="yes">n770/n800
+                <property name="items" translatable="yes" context="yes">n770/n800/n810
 HERMflasher</property>
               </widget>
               <packing>
@@ -30,17 +30,7 @@ HERMflasher</property>
               </packing>
             </child>
             <child>
-              <widget class="GtkButton" id="gochange">
+              <placeholder/>
-                <property name="width_request">32</property>
-                <property name="visible">True</property>
-                <property name="has_default">True</property>
-                <property name="label" translatable="yes" context="yes">&gt;</property>
-              </widget>
-              <packing>
-                <property name="expand">False</property>
-                <property name="fill">False</property>
-                <property name="position">1</property>
-              </packing>
             </child>
           </widget>
           <packing>
@@ -55,10 +45,11 @@ HERMflasher</property>
             <child>
               <widget class="GtkScrolledWindow" id="scrolledwindow1">
                 <property name="visible">True</property>
+                <property name="can_focus">False</property>
                 <property name="hscrollbar_policy">GTK_POLICY_AUTOMATIC</property>
                 <property name="vscrollbar_policy">GTK_POLICY_AUTOMATIC</property>
                 <child>
-                  <widget class="GtkTreeView" id="treeview1">
+                  <widget class="GtkTreeView" id="tree">
                     <property name="visible">True</property>
                   </widget>
                 </child>
@@ -70,14 +61,14 @@ HERMflasher</property>
                 <property name="border_width">3</property>
                 <property name="spacing">2</property>
                 <child>
-                  <widget class="GtkFileChooserButton" id="filechooserbutton2">
+                  <widget class="GtkFileChooserButton" id="file">
                   </widget>
                   <packing>
                     <property name="expand">False</property>
                   </packing>
                 </child>
                 <child>
-                  <widget class="GtkComboBox" id="combo1">
+                  <widget class="GtkComboBox" id="piece">
                     <property name="row_span_column">0</property>
                     <property name="column_span_column">0</property>
                     <property name="active">0</property>
@@ -100,12 +91,18 @@ xloader</property>
                       <widget class="GtkButton" id="button2">
                         <property name="visible">True</property>
                         <property name="label" context="yes">Remove</property>
+                        <property name="response_id">0</property>
+                        <signal name="clicked" handler="gui_remove"/>
+                        <signal name="activate" handler="gui_remove"/>
                       </widget>
                     </child>
                     <child>
                       <widget class="GtkButton" id="add">
                         <property name="visible">True</property>
                         <property name="label" context="yes">Add</property>
+                        <property name="response_id">0</property>
+                        <signal name="clicked" handler="gui_add"/>
+                        <signal name="activate" handler="gui_add"/>
                       </widget>
                       <packing>
                         <property name="position">1</property>
@@ -118,9 +115,10 @@ xloader</property>
                   </packing>
                 </child>
                 <child>
-                  <widget class="GtkCheckButton" id="checkbutton2">
+                  <widget class="GtkCheckButton" id="usbhost">
                     <property name="visible">True</property>
                     <property name="label" translatable="yes" context="yes">USB host mode</property>
+                    <property name="response_id">0</property>
                     <property name="draw_indicator">True</property>
                   </widget>
                   <packing>
@@ -130,9 +128,10 @@ xloader</property>
                   </packing>
                 </child>
                 <child>
-                  <widget class="GtkCheckButton" id="checkbutton3">
+                  <widget class="GtkCheckButton" id="rdmode">
                     <property name="visible">True</property>
                     <property name="label" translatable="yes" context="yes">R&amp;D mode</property>
+                    <property name="response_id">0</property>
                     <property name="draw_indicator">True</property>
                   </widget>
                   <packing>
@@ -145,6 +144,7 @@ xloader</property>
                   <widget class="GtkCheckButton" id="reboot">
                     <property name="visible">True</property>
                     <property name="label" translatable="yes" context="yes">Reboot</property>
+                    <property name="response_id">0</property>
                     <property name="draw_indicator">True</property>
                   </widget>
                   <packing>
@@ -171,7 +171,7 @@ xloader</property>
             <property name="visible">True</property>
             <property name="spacing">6</property>
             <child>
-              <widget class="GtkProgressBar" id="progressbar1">
+              <widget class="GtkProgressBar" id="pbar">
                 <property name="visible">True</property>
                 <property name="show_text">True</property>
               </widget>
@@ -184,6 +184,9 @@ xloader</property>
                     <property name="visible">True</property>
                     <property name="label" translatable="yes" context="yes">gtk-dialog-info</property>
                     <property name="use_stock">True</property>
+                    <property name="response_id">0</property>
+                    <signal name="clicked" handler="gui_information" object="main_window"/>
+                    <signal name="activate" handler="gui_information" object="main_window"/>
                   </widget>
                   <packing>
                     <property name="expand">False</property>
@@ -195,6 +198,9 @@ xloader</property>
                     <property name="visible">True</property>
                     <property name="label" translatable="yes" context="yes">gtk-execute</property>
                     <property name="use_stock">True</property>
+                    <property name="response_id">0</property>
+                    <signal name="clicked" handler="gui_run"/>
+                    <signal name="activate" handler="gui_run"/>
                   </widget>
                   <packing>
                     <property name="expand">False</property>
@@ -220,4 +226,54 @@ xloader</property>
       </widget>
     </child>
   </widget>
+  <widget class="GtkAboutDialog" id="information">
+    <property name="events">GDK_POINTER_MOTION_MASK | GDK_POINTER_MOTION_HINT_MASK | GDK_BUTTON_PRESS_MASK | GDK_BUTTON_RELEASE_MASK</property>
+    <property name="border_width">5</property>
+    <property name="title" translatable="yes" context="yes">About Glade</property>
+    <property name="resizable">False</property>
+    <property name="window_position">GTK_WIN_POS_CENTER_ON_PARENT</property>
+    <property name="type_hint">GDK_WINDOW_TYPE_HINT_DIALOG</property>
+    <property name="has_separator">False</property>
+    <property name="program_name">Glade</property>
+    <child internal-child="vbox">
+      <widget class="GtkVBox" id="dialog-vbox3">
+        <property name="visible">True</property>
+        <property name="events">GDK_POINTER_MOTION_MASK | GDK_POINTER_MOTION_HINT_MASK | GDK_BUTTON_PRESS_MASK | GDK_BUTTON_RELEASE_MASK</property>
+        <property name="spacing">2</property>
+        <child>
+          <widget class="GtkScrolledWindow" id="scrolledwindow2">
+            <property name="visible">True</property>
+            <property name="can_focus">True</property>
+            <property name="events">GDK_POINTER_MOTION_MASK | GDK_POINTER_MOTION_HINT_MASK | GDK_BUTTON_PRESS_MASK | GDK_BUTTON_RELEASE_MASK</property>
+            <property name="hscrollbar_policy">GTK_POLICY_AUTOMATIC</property>
+            <property name="vscrollbar_policy">GTK_POLICY_AUTOMATIC</property>
+            <child>
+              <widget class="GtkTextView" id="textview1">
+                <property name="visible">True</property>
+                <property name="can_focus">True</property>
+                <property name="events">GDK_POINTER_MOTION_MASK | GDK_POINTER_MOTION_HINT_MASK | GDK_BUTTON_PRESS_MASK | GDK_BUTTON_RELEASE_MASK</property>
+                <property name="pixels_below_lines">2</property>
+                <property name="editable">False</property>
+                <property name="cursor_visible">False</property>
+              </widget>
+            </child>
+          </widget>
+          <packing>
+            <property name="position">2</property>
+          </packing>
+        </child>
+        <child internal-child="action_area">
+          <widget class="GtkHButtonBox" id="dialog-action_area3">
+            <property name="visible">True</property>
+            <property name="events">GDK_POINTER_MOTION_MASK | GDK_POINTER_MOTION_HINT_MASK | GDK_BUTTON_PRESS_MASK | GDK_BUTTON_RELEASE_MASK</property>
+            <property name="layout_style">GTK_BUTTONBOX_END</property>
+          </widget>
+          <packing>
+            <property name="expand">False</property>
+            <property name="pack_type">GTK_PACK_END</property>
+          </packing>
+        </child>
+      </widget>
+    </child>
+  </widget>
 </glade-interface>

gui/main.c

@@ -21,10 +21,10 @@
 
 #define U(x) printf("%d\n",x); fflush(stdout);
 
+	GladeXML *xml;
 int main(int argc, char **argv)
 {
 	GtkWidget *w;
-	GladeXML *xml;
 
 	gtk_init(&argc, &argv);
 
@@ -40,6 +40,11 @@ int main(int argc, char **argv)
 	w = glade_xml_get_widget(xml, "main_window");
 	gtk_signal_connect(GTK_OBJECT(w), "destroy",
 		GTK_SIGNAL_FUNC(gtk_main_quit),NULL);
+{
+	GtkComboBox *piece = GTK_COMBO_BOX(glade_xml_get_widget(xml, "piece"));
+	gtk_combo_box_set_active(piece, 0);
+}
+
 	gtk_widget_show_all(w);
 
 	gtk_object_unref(GTK_OBJECT(xml));
@@ -47,3 +52,26 @@ int main(int argc, char **argv)
 	gtk_main();
 	return 0;	
 }
+extern void gui_run();
+extern void gui_run()
+{
+	printf("run\n");
+}
+
+extern void gui_add();
+extern void gui_add()
+{
+	GtkTreeView *tree = glade_xml_get_widget(xml, "tree");
+	GtkFileChooser *file = GTK_FILE_CHOOSER(glade_xml_get_widget(xml, "file"));
+	GtkComboBox *piece = GTK_COMBO_BOX(glade_xml_get_widget(xml, "piece"));
+
+	printf("ADD %s\n", gtk_file_chooser_get_filename(file));
+	printf("ADD %d\n", gtk_combo_box_get_active(piece));
+}
+
+extern void gui_information();
+void gui_information()
+{
+	printf("FUCKMENOT!\n");
+	fflush(stdout);
+}

src/Makefile

@@ -1,13 +1,16 @@
-VERSION=0.2
+include ../config.mk
 OBJ=main.o fiasco.o hexdump.o dump.o flash.o serial.o
 OBJ+=hash.o fpid.o query.o pieces.o utils.o devices.o console.o
 BIN=0xFFFF
+#LIBS=`${HAVE_USB} && echo -- '-lusb'`
+LIBS=`if [ "${HAVE_USB}" = 1 ]; then echo '-lusb'; fi`
 CFLAGS+=-DVERSION=\"${VERSION}\" -Wall -g -I .
+CFLAGS+=-pedantic -std=c99 -DHAVE_USB=${HAVE_USB}
 USBOBJ=../libusb/error.o ../libusb/usb.o ../libusb/descriptors.o
 USBOBJ+=../libusb/linux.o ## XXX not portable
 
 all: ${OBJ}
-	${CC} ${LDFLAGS} -o ${BIN} ${OBJ} -lusb
+	${CC} ${LDFLAGS} -o ${BIN} ${OBJ} ${LIBS}
 
 allusb: ${OBJ}
 	${CC} ${LDFLAGS} -o ${BIN} ${OBJ} ${USBOBJ}

src/console.c

@@ -1,6 +1,6 @@
 /*
  *  0xFFFF - Open Free Fiasco Firmware Flasher
- *  Copyright (C) 2007  pancake <pancake@youterm.com>
+ *  Copyright (C) 2007, 2008  pancake <pancake@youterm.com>
  *
  *  This program is free software: you can redistribute it and/or modify
  *  it under the terms of the GNU General Public License as published by
@@ -16,6 +16,7 @@
  *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#if HAVE_USB
 #include "main.h"
 #include "query.h"
 #include <stdio.h>
@@ -45,6 +46,7 @@ void cmd_help(char *line)
 
 void cmd_info(char *line)
 {
+	get_sw_version();
 	get_hw_revision(); // get hardware revision:
 	get_root_device(); // only for flashing
 	get_usb_mode();
@@ -60,14 +62,17 @@ void cmd_nanddump(char *line)
 	char out[128];
 	int ignbb;
 	int ignoob = -1;
-	sscanf(line, "%127s 0x%x 0x%x %127s %d %d", &dev, &from, &length, &out, &ignbb, &ignoob);
+
+	sscanf(line, "%127s 0x%x 0x%x %127s %d %d",
+		(char *)&dev, (unsigned int*)&from, (unsigned int *)&length,
+		(char *)&out, (int*)&ignbb, (int *)&ignoob);
+
 	if (ignoob == -1) {
-		printf("Invalid arguments.\n");
+		eprintf("Invalid arguments.\n");
-		printf("nanddump [dev] [start] [len] [out] [ignore-badblocks] [ignore-oob]\n");
+		eprintf("nanddump [dev] [start] [len] [out] [ignore-badblocks] [ignore-oob]\n");
-		printf("                  f.ex: nanddump /dev/mtd0 0x0 0x4000 xloader.bin 1 1\n");
+		eprintf("                  f.ex: nanddump /dev/mtd0 0x0 0x4000 xloader.bin 1 1\n");
-	} else {
+	} else
 		nanddump(dev, from, length, out, ignbb, ignoob);
-	}
 }
 
 void cmd_dump(char *line)
@@ -161,3 +166,4 @@ int console_prompt()
 
 	return 0;
 }
+#endif

src/devices.c

@@ -16,6 +16,7 @@
  *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#if HAVE_USB
 #include "main.h"
 #include <stdio.h>
 #include <string.h>
@@ -36,7 +37,7 @@
 struct devices supported_devices[SUPPORTED_DEVICES] = {
   { "FFFF", 0x000, 0x0000, 0x0000 },  // dummy
   { "unkn", 0x421, 0x3f00, 0x0000 },  // probably a development board
-  { "n770", 0x421, 0x0105, 0x0001 },  // my n770 
+  { "n770/n810", 0x421, 0x0105, 0x0001 },  // my n770 
   { "n800", 0x421, 0x04c3, 0x0001 },  // a n800 
   { 0 },
   { 0 }
@@ -56,7 +57,7 @@ int is_valid_device(struct usb_device_descriptor *udd)
 	for(i=1 ; ptr.vendor_id; ptr = supported_devices[++i])
 		if ((udd->idVendor  == ptr.vendor_id)
 		&&  (udd->idProduct == ptr.product_id)) {
-                        D printf("found %s\n", supported_devices[i]);
+                        D printf("found %s\n", supported_devices[i].name);
 			return i;
 		}
 
@@ -116,3 +117,4 @@ int usb_device_found(struct usb_device_descriptor *udd, struct devices *it_devic
 
 	return 0;
 }
+#endif

src/dump.c

@@ -18,7 +18,6 @@
 
 #include "main.h"
 #include "hexdump.h"
-#include <usb.h>
 #include <stdio.h>
 #include <stdlib.h>
 #include <string.h>
@@ -81,8 +80,11 @@ __rf_extract_exit:
 #include <sys/ioctl.h>
 #include <sys/types.h>
 #include <sys/stat.h>
-#include <asm/types.h>
+//#include <asm/types.h>
 #include <mtd/mtd-user.h>
+#ifndef loff_t
+#define loff_t off_t
+#endif
 
 #define M_RDONLY   0x00000001
 #define M_RDRW     0x00000002
@@ -242,7 +244,8 @@ closeall:
 	return 1;
 }
 
-int nanddump(char *mtddev, unsigned long start_addr, unsigned long length, char *dumpfile, int isbl)
+// XXX warning ioob is not used
+int nanddump(char *mtddev, unsigned long start_addr, unsigned long length, char *dumpfile, int isbl, int ioob)
 {
 	unsigned char readbuf[2048];
 	int oobinfochanged = 0 ;
@@ -379,6 +382,7 @@ int nanddump(char *mtddev, unsigned long start_addr, unsigned long length, char
 
 		/* Write out page data */
 		//if (pretty_print) dump_bytes(readbuf, bs);
+		write(ofd, readbuf, bs);
 		progressbar(ofs, end_addr);
 
 		// OOB STUFF //
@@ -543,20 +547,20 @@ int reverse_extract_pieces(char *dir)
 	// TODO: get values from /proc/mtd ???
 
 	//rf_extract("/dev/mtd0", is_n800()?0x200:0, 0x003600, "xloader.bin");
-	nanddump("/dev/mtd0", is_n800()?0x200:0, 0x4000, "xloader.bin", 1); // 0x3600 size?
+	nanddump("/dev/mtd0", is_n800()?0x200:0, 0x4000, "xloader.bin", 1,0); // 0x3600 size?
 	//rf_extract("/dev/mtd0", 0x004000, 0x01ffff,  "secondary.bin");
-	nanddump("/dev/mtd0", 0x004000, 0,  "secondary.bin", 1);
+	nanddump("/dev/mtd0", 0x004000, 0,  "secondary.bin", 1,0);
-	nanddump("/dev/mtd1", 0, 0,  "config.bin", 0);
+	nanddump("/dev/mtd1", 0, 0,  "config.bin", 0,0);
 	//rf_extract("/dev/mtd2", 0x000800, 0x200000,  "zImage");
-	nanddump("/dev/mtd2", 0x000800, 0,  "zImage", 0);
+	nanddump("/dev/mtd2", 0x000800, 0,  "zImage", 0,0);
 	//rf_extract("/dev/mtd3", 0x000000, 0x1D00000, "initfs.jffs2");
-	nanddump("/dev/mtd3", 0x000000, 0, "initfs.jffs2", 0);
+	nanddump("/dev/mtd3", 0x000000, 0, "initfs.jffs2", 0,0);
 
 	printf("\n\nExtract rootfs? (y/N): "); fflush(stdout);
 	read(0, &reply, 1);
 	if (reply=='y'||reply=='Y') {
 		//rf_extract("/dev/mtd4", 0x000000, 0x6000000, "rootfs.jffs2");
-		nanddump("/dev/mtd4", 0x000000, 0, "rootfs.jffs2", 0);
+		nanddump("/dev/mtd4", 0x000000, 0, "rootfs.jffs2", 0,0);
 	} else	printf("*** Ignoring rootfs\n");
 
 	printf("\n\nStrip dumped files? (y/N): "); fflush(stdout);

src/fiasco.c

@@ -16,119 +16,278 @@
  *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
-#include "main.h"
 #include <stdio.h>
 #include <string.h>
 #include <stdlib.h>
+#include <fcntl.h>
 #include <unistd.h>
 #include <sys/types.h>
 #include <sys/stat.h>
-#include <fcntl.h>
+#include <arpa/inet.h>
+#include "main.h"
+#include "hash.h"
 
-#warning The FIASCO format is not yet fully implemented.
+void (*fiasco_callback)(struct header_t *header) = NULL;
 
-off_t piece_header_to_size(unsigned char *header)
+int openfiasco(char *name)
 {
-	off_t sz = 0;
+	struct header_t header;
-	sz += header[0x15+3];
+	unsigned char buf[128];
-	sz += header[0x15+2] << 8;
+	unsigned char data[128];
-	sz += header[0x15+1] << 16;
+	unsigned int namelen;
-	sz += header[0x15+0] << 24;
+	off_t off;
-	return sz;
+	int i;
-}
+	header.fd = open(name, O_RDONLY);
 
-int piece_header_is_valid(unsigned char *header)
+	if (header.fd == -1) {
-{
+		fprintf(stderr, "Cannot open %s\n", name);
-	if (header[0]=='T' && header[1]=='\x02')
 		return 1;
+	}
+
+	/* read header */
+	read(header.fd, buf, 5);
+	if (buf[0] != 0xb4) {
+		printf("Invalid header\n");
+		return close(header.fd);
+	}
+	memcpy(&namelen,buf+1,4);
+	namelen = ntohl(namelen);
+	if (namelen>128) {
+		printf("Stupid length at header. Is this a joke?\n");
+		return close(header.fd);
+	}
+	memset(buf,'\0', 128);
+	read(header.fd, buf, namelen);
+
+	printf("Fiasco version: %2d\n", buf[3]);
+	strcpy(header.fwname, (char *)buf+6);
+	for(i=6;i<namelen;i+=strlen((char *)(buf+i))+1)
+		printf("Name: %s\n", buf+i);
+
+	/* walk the tree */
+	while(1) {
+		if (read(header.fd, buf, 9)<9)
+			break;
+
+		if (buf[0] != 0x54) { // 'T'
+			printf("unexpected header at 0x%x, found %02x %02x %02x\n", 
+				((int)lseek(header.fd, 0, SEEK_CUR))-9,
+				buf[0], buf[1], buf[2]);
+			break;
+		}
+		header.hash = buf[7]<<8|buf[8];
+
+		/* piece name */
+		memset(data, '\0', 13);
+		if (read(header.fd, data, 12)<12)
+			break;
+
+		if (data[0] == 0xff) {
+			printf(" [eof]\n");
+			break;
+		} else printf(" %s\n", data);
+		strcpy(header.name, (char *)data);
+
+		if (read(header.fd, buf, 9)<9)
+			break;
+		memcpy(&header.size, buf,4);
+		header.size = ntohl(header.size);
+		printf("   size:    %d bytes\n", header.size);
+		printf("   hash:    %04x\n", header.hash);
+		//printf("BYTE: %02x %02x %02x %02x %02x\n", 
+		//	buf[4], buf[5], buf[6], buf[7], buf[8]);
+		/* XXX this is not ok */
+		//printf("BUF8: %02x\n", buf[8]);
+		while (buf[8] && buf[8]>'0' && buf[8] < '9') {
+			if (read(header.fd, data, 1)<1)
+				break;
+			i = data[0];
+			if (read(header.fd, data, i)<i)
+				break;
+			if (data[0])
+			printf("   version: %s\n", data);
+			strcpy(header.version, (char *)data);
+			if (read(header.fd, buf+8, 1)<1)
+				break;
+		}
+		/* callback */
+		off = lseek(header.fd, 0, SEEK_CUR);
+		if (fiasco_callback != NULL) {
+			fiasco_callback(&header);
+			free(header.data);
+			continue;
+		}
+		// XXX dup
+		lseek(header.fd, off, SEEK_SET);
+		lseek(header.fd, header.size, SEEK_CUR);
+	}
 	return 0;
 }
 
-#define piece_header_to_name(x) x+0x9;
+void fiasco_data_read(struct header_t *header)
+{
+	header->data = (unsigned char *)malloc(header->size);
+	if (header->data == NULL) {
+		printf("Cannot alloc %d bytes\n", header->size);
+		return;
+	}
+	read(header->fd, header->data, header->size);
+}
 
-/*
+/* fiasco writer */
- * Teh Fiasco firmware parser lives here!
+int fiasco_new(const char *filename, const char *name)
- */
-int fiasco_read_image(char *file)
 {
 	int fd;
-	unsigned char header[5];
+	//int len = htonl(strlen(name)+1+6+14);
-	unsigned char version[55];
-	char *version2;
 
-	fd = open(file, O_RDONLY);
+	fd = open(filename, O_RDWR|O_CREAT, 0644);
-
+	if (fd == -1)
-	printf("WARNING: Fiasco firmware is not yet fully supported. Don't relay on it ATM.\n");
-
-	if (fd == -1) {
-		printf("Cannot open fiasco image.\n");
 		return -1;
+#if 1
+	write(fd, "\xb4\x00\x00\x00\x14\x00\x00\x00\x01\xe8\x0e", 11);
+	write(fd, "OSSO UART+USB", 14);
+#else
+	/* 2nd format doesnt works. atm stay with old one */
+	write(fd, "\xb4", 1);
+	write(fd, &len, 4);
+	/* version header */
+	write(fd, "\x00\x00\x00\x02\xe8\x0e", 6);
+	/* firmware type */
+	write(fd, "OSSO UART+USB", 14);
+	/* firmware name */
+	write(fd, name, strlen(name));
+	write(fd, "", 1);
+#endif
+	return fd;
+}
+
+int fiasco_add_eof(int fd)
+{
+#if 0
+	unsigned char buf[120];
+	if (fd == -1)
+		return -1;
+	memset(buf,'\xff', 120);
+	write(fd, buf, 120);
+#endif
+	return 0;
+}
+
+
+int fiasco_add(int fd, const char *name, const char *file, const char *version)
+{
+	int gd,ret;
+	unsigned int sz;
+	unsigned char len;
+	unsigned short hash;
+	unsigned char *ptr = (unsigned char *)&hash;
+	char buf[4096];
+	char bname[32];
+
+	if (fd == -1)
+		return -1;
+	if (file == NULL)
+		return -1;
+	gd = open(file, O_RDONLY);
+	if (gd == -1)
+		return -1;
+
+	sz = htonl((unsigned int) lseek(gd, 0, SEEK_END));
+	lseek(gd, 0, SEEK_SET);
+	// 4 bytes big endian
+	//write(fd, "T\x02\x2e\x19\x01\x01\x00", 7); // header?
+	write(fd, "T\x01\x2e\x19\x01\x01\x00", 7); // header (old piece format)
+	/* checksum */
+	hash = do_hash_file(file);
+	ptr[0]^=ptr[1]; ptr[1]=ptr[0]^ptr[1]; ptr[0]^=ptr[1];
+	write(fd, &hash, 2);
+	printf("hash: %04x\n", hash);
+
+	memset(bname, '\0', 13);
+	if (name == NULL)
+		name = fpid_file(file);
+	/* failback */
+	if (name == NULL)
+		name = file;
+
+	strncpy(bname, name, 12);
+	write(fd, bname, 12);
+
+	write(fd, &sz, 4);
+	if (version) {
+		/* append metadata */
+		write(fd, "\x00\x00\x00\x00\x31", 5);
+		len = strlen(version);
+		write(fd, &len, 1);
+		write(fd, version, len);
+		write(fd, "\x00\x9b", 2);
+	} else {
+		write(fd, "\x00\x00\x00\x00\x9b", 5);
 	}
 
-	// b4 00 00 00 00 36
+	while(1) {
-	if (read(fd, header, 5) != 5) {
+		ret = read(gd, buf, 4096);
-		printf("Error reading fiasco header\n");
+		if (ret<1)
-		goto __fiasco_read_image_end;
-	}
-
-	if (header[0] != 0xb4) {
-		printf("Invalid fiasco signature.\n");
-		goto __fiasco_read_image_end;
-	}
-	// skip 6 bytes
-	read(fd, version, 6);
-
-	// print version header
-	if (read(fd, version, 55) != 55) {
-		printf("Error reading fiasco version.\n");
-		goto __fiasco_read_image_end;
-	}
-
-	printf("# Fiasco header information:\n");
-	printf("# ==========================\n");
-	printf("# firmware type:    %s\n", version);
-	version2 = version+strlen((char *)version)+3;
-	if (*version2=='.')
-		printf("firmware version: (null) (old firmware? no version string found?)\n");
-	else printf("firmware version: %s\n", version2);
-
-	// pieces:
-	// after the version2 string starts the header-body loop love
-	lseek(fd, 0xf + strlen(version2) + strlen(version), SEEK_SET);
-	do {
-		char piece_header[30];
-		char description[256];
-		unsigned char desc_len;
-		char *name;
-		off_t size;
-		off_t tmp = lseek(fd, 0, SEEK_CUR);
-
-		size = read(fd, piece_header, 30);
-		if (size != 30) {
-			fprintf(stderr, "Unexpected end of file\n");
 			break;
+		write(fd, buf, ret);
+	}
+
+	return 0;
+}
+
+int fiasco_pack(int optind, char *argv[])
+{
+	const char *file = argv[optind];
+	char *type;
+	int fd, ret;
+
+	fd = fiasco_new(file, file); // TODO use a format here
+	if (fd == -1)
+		return 1;
+
+	printf("Package: %s\n", file);
+	while((file=argv[++optind])) {
+		type = (char *)fpid_file(file);
+		printf("Adding %s: %s..\n", type, file);
+		ret = fiasco_add(fd, type, file, NULL);
+		if (ret<0) {
+			printf("Error\n");
+			close(fd);
+			return 1;
 		}
-		dump_bytes(piece_header,30);
+	}
-		if (!piece_header_is_valid(piece_header)) {
+	fiasco_add_eof(fd);
-			fprintf(stderr, "Oops. Invalid piece header.\n");
+	printf("Done!\n");
-			break;
-		}
-		size = piece_header_to_size(piece_header);
-		name = piece_header_to_name(piece_header);
-		printf("# %s is %lld bytes\n", name, size);
-
-		read(fd, description, 255);
-		printf("#   version: %s\n", description);
-		/* lseek foreach subimage */
-		lseek(fd, tmp, SEEK_SET);
-		lseek(fd, strlen(description) + 0x20, SEEK_CUR);
-		printf("rsc '%s' %lld '%s.bin' 0 %lld\n", file, lseek(fd,0,SEEK_CUR), name, size);
-		lseek(fd, size, SEEK_CUR);
-	} while(1);
-
-	//printf("Image '%s', size %d bytes.\n", image, size);
-
-__fiasco_read_image_end:
 	close(fd);
 	return 0;
 }
+
+/* local code */
+#if 0
+void my_callback(int fd, struct header_t *header)
+{
+	fiasco_data_read(header);
+	//read(fd, buf, header->size);
+	printf("Dumping %s\n", header->name);
+	printf("DATA: %02x\n", header->data[0]);
+	fiasco_data_free(header);
+}
+
+int main(int argc, char **argv)
+{
+	if (argc!=2) {
+		printf("Usage: unfiasco [file]\n");
+		return 1;
+	}
+
+/*
+	fd = fiasco_new("myfiasco", "pancake-edition");
+	fiasco_add(fd, "kernel", "zImage", "2.6.22");
+	close(fd);
+*/
+
+//	fiasco_callback = &my_callback;
+
+	return openfiasco(argv[1]);
+}
+#endif

src/flash.c

@@ -16,10 +16,10 @@
  *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#if HAVE_USB
 #include "main.h"
 #include "hash.h"
 #include "hexdump.h"
-#include <usb.h>
 #include <stdio.h>
 #include <string.h>
 #include <stdlib.h>
@@ -195,3 +195,4 @@ void flash_image(char *filename, char *piece, char *version)
 	}
 	printf("Flash done succesfully.\n");
 }
+#endif

src/fpid.c

@@ -20,7 +20,7 @@
 #include <stdio.h>
 #include <string.h>
 
-char *fpid_file(char *filename)
+const char *fpid_file(const char *filename)
 {
 	FILE *fd;
 	char buf[512];
@@ -45,11 +45,9 @@ char *fpid_file(char *filename)
 	size = ftell(fd);
 	fclose(fd);
 
-#if 0
 	if (!memcmp(b+0x34, "2NDAPE", 6))
-		return PIECE_2ND;
+		return pieces[PIECE_2ND];
 	else
-#endif
 	if (!memcmp(b+0x04, "NOLOScnd", 8))
 		return pieces[PIECE_SECONDARY];
 	else

src/hash.c

@@ -27,7 +27,7 @@ usho do_hash(usho *b, int len)
 	return result;
 }
 
-usho do_hash_file(char *filename)
+usho do_hash_file(const char *filename)
 {
 	unsigned char buf[BSIZE];
 	FILE *fd = fopen(filename, "r");

src/hash.h

@@ -5,6 +5,6 @@
 #define BSIZE 0x20000
 
 usho do_hash(usho *b, int len);
-usho do_hash_file(char *filename);
+usho do_hash_file(const char *filename);
 
 #endif

src/main.c

@@ -24,8 +24,11 @@
 #include <getopt.h>
 
 /* global pr0n */
+#if HAVE_USB
+#include <usb.h>
 struct usb_device *device  = NULL;
 struct usb_dev_handle *dev = NULL;
+#endif
 char  *fiasco_image        = NULL;
 char  *boot_cmdline        = NULL;
 char  *reverseto           = NULL;
@@ -35,32 +38,33 @@ int    usb_mode            = -1;
 int    root_device         = -1;
 int    verbose             = 0;
 int    identify            = 0;
-int    reboot              = 0;
+int    moboreboot          = 0;
 int    unpack              = 0;
 int    info                = 0;
 
 /* global structs */
 char *pieces[] = {
-  "xloader",    // xloader.bin
+	"xloader",    // xloader.bin
-  "secondary",  // secondary.bin
+	"2nd",        // 2nd
-  "kernel",     // zImage
+	"secondary",  // secondary.bin
-  "initfs",     // jffs'd initfs
+	"kernel",     // zImage
-  "rootfs",     // 80mB of blob
+	"initfs",     // jffs'd initfs
-  "omap-nand",  // 8kB of food for the nand
+	"rootfs",     // 80mB of blob
-  NULL
+	"omap-nand",  // 8kB of food for the nand
+	NULL
 };
 
 char *modes[]={
-  "host",
+	"host",
-  "peripheral",
+	"peripheral",
-  NULL
+	NULL
 };
 
 char *root_devices[] = {
-  "flash",
+	"flash",
-  "mmc",
+	"mmc",
-  "usb",
+	"usb",
-  NULL
+	NULL
 };
 
 
@@ -73,27 +77,33 @@ void show_usage()
 {
 	int i;
 	show_title();
-
+#if HAVE_USB
-	printf(" -b [arg]       boots the kernel with arguments\n");
+	printf("Over USB:\n");
-	printf(" -e [path]      dump and extract pieces to path\n");
+	printf(" -b [arg]        boots the kernel with arguments\n");
-	printf(" -r [0|1]       disable/enable R&D mode\n");
+	printf(" -c              console prompt mode\n");
-	printf(" -f <flags>     set the given RD flags (see '-f help')\n");
+	printf(" -d [vid:pid]    injects a usb device into the supported list\n");
+	printf(" -D [0|1|2]      sets the root device to flash (0), mmc (1) or usb (2)\n");
+	printf(" -f <flags>      set the given RD flags (see '-f help')\n");
+	printf(" -i              show device information (let standby mode)\n");
+	printf(" -l              list supported usb device ids\n");
 	printf(" -p [[p%%]file]  piece-of-firmware %% file-where-this-piece-is\n");
-	printf(" -u [fiasco]    unpack target fiasco image\n");
+	printf(" -r [0|1]        disable/enable R&D mode\n");
-	printf(" -U [0|1]       disable/enable the usb host mode\n");
+	printf(" -R              reboot the omap board\n");
-	printf(" -s [serial]    serial port console (minicom like terminal)\n");
+	printf(" -U [0|1]        disable/enable the usb host mode\n");
-	printf(" -C [/dev/mtd]  check bad blocks on mtd\n");
+#endif
-	printf(" -c             console prompt mode\n");
+	printf("Local stuff:\n");
-	printf(" -h             show this help message\n");
+	printf(" -s [serial]     serial port console (minicom like terminal)\n");
-	printf(" -i             show device information (let standby mode)\n");
+	printf(" -h              show this help message\n");
-	printf(" -I [piece]     identify a firmware piece\n");
+	printf(" -C [/dev/mtd]   check bad blocks on mtd\n");
-	printf(" -l             list supported usb device ids\n");
+	printf(" -e [path]       dump and extract pieces to path\n");
-	printf(" -d [vid:pid]   injects a usb device into the supported list\n");
+	printf(" -F [fiasco]     flash a fiasco firmware image\n");
-	printf(" -D [0|1|2]     sets the root device to flash (0), mmc (1) or usb (2)\n");
+	printf(" -H [file]       calculate hash for file\n");
-	printf(" -R             reboot the omap board\n");
+	printf(" -I [piece]      identify a firmware piece\n");
-	printf(" -x             extract configuration entries from /dev/mtd1\n");
+	printf(" -P [new-fiasco] creates a new fiasco package, pieces as arguments\n");
-	printf(" -v             be verbose and noisy\n");
+	printf(" -u [fiasco]     unpack target fiasco image\n");
-	printf(" -V             show 0xFFFF version information\n");
+	printf(" -v              be verbose and noisy\n");
+	printf(" -V              show 0xFFFF version information\n");
+	printf(" -x              extract configuration entries from /dev/mtd1\n");
 	printf("Pieces are: ");
 	for(i=0;pieces[i];i++) printf("%s ", pieces[i]); printf("\n");
 	// serial port support is not yet done (cold flash is for flashing the 8kB nand)
@@ -102,12 +112,37 @@ void show_usage()
 	exit(0);
 }
 
-void unpack_fiasco_image(char *file)
+
+void unpack_callback(struct header_t *header)
 {
-	fiasco_read_image(file);
+	FILE *fd = fopen(header->name, "wb");
-	// TODO
+	if (fd == NULL) {
+		printf("Cannot open file.\n");
+		return;
+	}
+	fiasco_data_read(header);
+	fwrite(header->data, header->size, 1, fd);
+	fclose(fd);
 }
 
+void unpack_fiasco_image(char *file)
+{
+	printf("Dumping firmware pieces to disk.\n");
+	fiasco_callback = &unpack_callback;
+	openfiasco( file );
+}
+
+int fiasco_flash(char *file)
+{
+	/* TODO */
+	fiasco_callback = NULL;
+	openfiasco( file );
+
+	printf("\nTODO: Implement the fiasco flashing here.\n");
+	return -1;
+}
+
+#if HAVE_USB
 int connect_via_usb()
 {
         struct usb_device_descriptor udd;
@@ -140,7 +175,8 @@ int connect_via_usb()
                         return 1;
 	        }
 
-        	if ( usb_claim_interface(dev, 2) < 0) { // 2 or 0
+        	if ( usb_claim_interface(dev, 2) < 0) {
+		//device->config->interface->altsetting->bInterfaceNumber) < 0) { // 2 or 0
 	        	D perror("usb_claim_interface");
 
                         // Something is broken if closing fails.
@@ -155,7 +191,7 @@ int connect_via_usb()
                         continue;
         	}
 
-        	if (usb_set_altinterface(dev, 1) < 0) {
+        	if (usb_set_altinterface(dev, 1) <0) { //device->config->interface->altsetting->bAlternateSetting) < 0) {
 	        	D perror("usb_set_altinterface");
 
                         // Something is broken if closing fails.
@@ -180,17 +216,30 @@ int connect_via_usb()
 
 	return 0;
 }
+#endif
 
 int main(int argc, char **argv)
 {
 	int c;
 
-	while((c = getopt(argc, argv, "C:cp:vVhRu:ib:U:r:e:ld:I:D:f:s:x")) != -1) {
+	while((c = getopt(argc, argv, "C:cp:PvVhRu:ib:U:r:e:ld:I:D:f:F:s:xH:")) != -1) {
 		switch(c) {
+		case 'H':
+			printf("xorpair: %04x\n", do_hash_file(optarg));
+			return 0;
 		case 'x':
 			return dump_config();
+#if HAVE_USB
 		case 'c':
 			return console_prompt();
+		case 'b':
+			boot_cmdline = optarg;
+			break;
+		case 'U':
+			usb_mode = atoi(optarg);
+			break;
+		case 'F':
+			return fiasco_flash(optarg);
 		case 'd':
 			sscanf(optarg, "%04hx:%04hx", 
 				&supported_devices[SUPPORTED_DEVICES-2].vendor_id,
@@ -200,11 +249,6 @@ int main(int argc, char **argv)
 		case 'D':
 			root_device = atoi(optarg);
 			break;
-		case 'e':
-			reverseto = optarg;
-			break;
-		case 's':
-			return console(optarg);
 		case 'f':
 			if (!strcmp(optarg,"help")) {
 			printf("* Flags are composed of:\n");
@@ -216,34 +260,40 @@ int main(int argc, char **argv)
 			exit(1);
  			}
 			rd_flags = (unsigned short) strtoul(optarg, NULL, 16);
-		case 'U':
-			usb_mode = atoi(optarg);
 			break;
 		case 'r':
 			rd_mode = atoi(optarg);
 			break;
-		case 'b':
+		case 'l':
-			boot_cmdline = optarg;
+			list_valid_devices();
+			return 0;
+		case 'p':
+			add_piece(optarg);
 			break;
+		case 'i':
+			info = 1;
+			break;
+		case 'R':
+			moboreboot = 1;
+			break;
+#endif
+		case 'e':
+			reverseto = optarg;
+			break;
+		case 's':
+			return console(optarg);
 		case 'u':
 			fiasco_image = optarg;
 			unpack = 1;
 			break;
-		case 'p':
+		case 'P':
-			add_piece(optarg);
+			return fiasco_pack(optind, argv);
-			break;
-		case 'l':
-			list_valid_devices();
-			return 0;
 		case 'I':
 			printf("%s: %s\n", fpid_file(optarg), optarg);
 			identify = 1;
 			break;
 		case 'C':
 			return check_badblocks(optarg);
-		case 'i':
-			info = 1;
-			break;
 		case 'v':
 			verbose = 1;
 			break;
@@ -253,9 +303,6 @@ int main(int argc, char **argv)
 		case 'V':
 			printf("%s\n", VERSION);
 			return 0;
-		case 'R':
-			reboot = 1;
-			break;
 		}
 	}
 
@@ -270,13 +317,13 @@ int main(int argc, char **argv)
 	&&	(rd_flags     == -1)
 	&&	(rd_mode      == -1)
 	&&	(info         == 0)
-	&&	(reboot       == 0)
+	&&	(moboreboot       == 0)
 	&&	(usb_mode     == -1)
 	&& 	(root_device  == -1))
 	{
-		printf("Usage: 0xFFFF [-hvVRi] [-e path] [-U 0|1] [-p [piece%%]file [-p ...]]\n");
+		printf("0xFFFF [-chilRvVx] [-C mtd-dev] [-d vid:pid] [-D 0|1|2] [-e path] [-f flags]\n");
-		printf("              [-b boot-args] [-I piece [-I ...]] [-u fiasco-image] [-x]\n");
+		printf("       [-F fiasco] [-H hash-file] [-I piece] [-p [piece%%]file]] [-r 0|1]\n");
-		printf("              [-D 0|1|2] [-F rd flags] [-s serial-dev] [-c] [-C mtd-dev]\n");
+		printf("       [-s serial-dev] [-u fiasco-image] [-U 0|1] | [-P new-fiasco] [piece1] [2] ..\n");
 		return 1;
 	}
 
@@ -290,6 +337,7 @@ int main(int argc, char **argv)
 		return 0;
 	}
 
+#if HAVE_USB
         if (connect_via_usb()) {
                 fprintf(stderr, "Cannot connect to device. It is possibly not in boot stage.\n");
                 return 0;
@@ -326,8 +374,9 @@ int main(int argc, char **argv)
 	if (boot_cmdline)
 		boot_board(boot_cmdline);
 
-	if (reboot)
+	if (moboreboot)
 		reboot_board();
+#endif
 
 	return 0;
 }

src/main.h

@@ -2,6 +2,9 @@
 #ifndef _INCLUDE_MAIN_H_
 #define _INCLUDE_MAIN_H_
 
+#include "hash.h"
+#include "nolo.h"
+
 #define _FILE_OFFSET_BITS 64
 #define _GNU_SOURCE
 
@@ -15,9 +18,16 @@ void check_nolo_order();
 extern struct usb_dev_handle *dev;
 unsigned long get_file_size(char *file);
 void progressbar(unsigned long long part, unsigned long long total);
-char *fpid_file(char *filename);
+const char *fpid_file(const char *filename);
 int add_piece(char *piece);
+void eprintf(const char *format, ...);
 
+#include <limits.h>
+#ifndef PATH_MAX
+#define PATH_MAX 4096
+#endif
+
+#if HAVE_USB
 #include <usb.h>
 
 extern struct usb_device *device;
@@ -27,6 +37,8 @@ void list_valid_devices();
 int usb_device_found(struct usb_device_descriptor *udd, struct devices *it_device);
 int console(const char *device);
 int connect_via_usb();
+#endif
+
 int console_prompt();
 
 //
@@ -40,9 +52,6 @@ extern int verbose;
 #define CMD_WRITE 64
 #define CMD_QUERY 192
 
-#define NOLO_GET_STATUS   1
-#define NOLO_GET_BOARD_ID 2
-#define NOLO_GET_VERSION  3
 
 struct piece_t {
 	char *name;
@@ -65,6 +74,7 @@ extern struct piece_t pcs[10];
 
 enum {
 	PIECE_XLOADER = 0,
+	PIECE_2ND,
 	PIECE_SECONDARY,
 	PIECE_KERNEL,
 	PIECE_INITFS,
@@ -73,8 +83,29 @@ enum {
 	PIECE_LAST
 };
 
+struct header_t {
+	int fd;
+	char fwname[128];
+	char name[128];
+	char version[128];
+	unsigned short hash;
+	unsigned int size;
+	unsigned char *data;
+};
+
 extern char *pieces[];
 extern char *modes[];
 extern char *root_devices[];
 
+// fiasco
+int openfiasco(char *name);
+int fiasco_new(const char *filename, const char *name);
+void fiasco_data_read(struct header_t *header);
+int fiasco_add_eof(int fd);
+extern void (*fiasco_callback)(struct header_t *header);
+int fiasco_add(int fd, const char *name, const char *file, const char *version);
+int fiasco_pack(int optind, char *argv[]);
+int nanddump(char *mtddev, unsigned long start_addr, unsigned long length, char *dumpfile, int isbl, int ioob);
+
+
 #endif

src/nolo.h

@@ -0,0 +1,7 @@
+
+#define NOLO_GET_STATUS   1
+#define NOLO_GET_BOARD_ID 2
+#define NOLO_GET_VERSION  3
+#define NOLO_GET_HWVERSION 4
+#define NOLO_SET_RDFLAGS   16
+#define NOLO_GET_RDFLAGS  17

src/pieces.c

@@ -55,7 +55,7 @@ int add_piece(char *piece)
 		pcs[pcs_n].vers = NULL; // TODO version string not yet supported
 	} else {
 		/*/ autodetect piece type */
-		pcs[pcs_n].type = fpid_file(piece);
+		pcs[pcs_n].type = (char *)fpid_file(piece);
 		if (pcs[pcs_n].type == NULL) {
 			printf("Use -p [piece]:[file]\n");
 			printf("Pieces: ");

src/query.c

@@ -1,6 +1,6 @@
 /*
  *  0xFFFF - Open Free Fiasco Firmware Flasher
- *  Copyright (C) 2007  pancake <pancake@youterm.com>
+ *  Copyright (C) 2007,2008  pancake <@youterm.com>
  *
  *  This program is free software: you can redistribute it and/or modify
  *  it under the terms of the GNU General Public License as published by
@@ -16,6 +16,8 @@
  *  along with this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#if HAVE_USB
+
 #include "main.h"
 #include <stdio.h>
 #include <string.h>
@@ -116,7 +118,7 @@ int set_rd_mode(unsigned short mode)
 	if (((short)mode)==-1)
 		return 1;
 
-	if (usb_control_msg(dev, CMD_WRITE, 16, mode, 0, 0, 0, 2000) == -1) {
+	if (usb_control_msg(dev, CMD_WRITE, NOLO_SET_RDFLAGS, mode, 0, 0, 0, 2000) == -1) {
 		fprintf(stderr, "Cannot set R&D flags.\n");
 		return 1;
 	}
@@ -134,7 +136,8 @@ int get_hw_revision()
 	unsigned char string[512];
 	int i = 0;
 
-	if (usb_control_msg(dev, CMD_QUERY, 4, 0, 0, (char *)string, 512, 2000) == -1) {
+	memset(string,'\0',512);
+	if (usb_control_msg(dev, CMD_QUERY, NOLO_GET_HWVERSION, 0, 0, (char *)string, 512, 2000) == -1) {
 		fprintf(stderr, "Cannot query hw revision.\n");
 		return -1;
 	}
@@ -157,7 +160,7 @@ int get_rd_mode()
 {
 	char isrd = 1;
 
-	if (usb_control_msg(dev, CMD_QUERY, 17, 0, 0, (char *)&isrd, 1, 2000) == -1) {
+	if (usb_control_msg(dev, CMD_QUERY, NOLO_GET_RDFLAGS, 0, 0, (char *)&isrd, 1, 2000) == -1) {
 		fprintf(stderr, "Cannot query rd mode.\n");
 		return -1;
 	}
@@ -170,7 +173,7 @@ int get_root_device()
 {
 	unsigned char opcode;
 
-	if (usb_control_msg(dev, CMD_QUERY, 17, 0, 1, (char *)&opcode, 1, 2000) < 0) {
+	if (usb_control_msg(dev, CMD_QUERY, NOLO_GET_RDFLAGS, 0, 1, (char *)&opcode, 1, 2000) < 0) {
 		fprintf(stderr, "Cannot query root device\n");
 		return -1;
 	}
@@ -197,7 +200,7 @@ int set_root_device(unsigned short root_device)
 		return -1;
 	}
 
-	if (usb_control_msg(dev, CMD_WRITE, 16, root_device, 1, 0, 0, 2000) == -1) {
+	if (usb_control_msg(dev, CMD_WRITE, NOLO_SET_RDFLAGS, root_device, 1, 0, 0, 2000) == -1) {
 		fprintf(stderr, "Cannot set root device\n");
 		return -1;
 	}
@@ -281,7 +284,7 @@ int get_rd_flags()
 {
 	unsigned short flags = 0;
 	
-	if (usb_control_msg(dev, CMD_QUERY, 17, 0, 3, (void *) &flags, sizeof(flags), 2000) == -1) {
+	if (usb_control_msg(dev, CMD_QUERY, NOLO_GET_RDFLAGS, 0, 3, (void *) &flags, sizeof(flags), 2000) == -1) {
 		fprintf(stderr, "Cannot get rd flags\n");
 		return -1;
 	}
@@ -301,7 +304,7 @@ int get_nolo_version()
 	unsigned int version; // ensure uint is at least 32 bits
 
 	//if (usb_control_msg(dev, CMD_QUERY, 3, 0, 1, (char *)&version, 4 , 2000) < 0) {
-	if (usb_control_msg(dev, CMD_QUERY, 3, 0, 0, (char *)&version, 4 , 2000) < 0) {
+	if (usb_control_msg(dev, CMD_QUERY, NOLO_GET_VERSION, 0, 0, (char *)&version, 4 , 2000) < 0) {
 		fprintf(stderr, "Cannot query nolo version. Old bootloader version?\n");
 		exit(1);
 	}
@@ -328,6 +331,7 @@ int get_sw_version()
 		fprintf(stderr, "error: cannot write query 18\n");
 		return 0;
 	}
+	bytes[0]='\0';
 	ret = usb_control_msg(dev, CMD_QUERY, 20, 0, 0, (char *)&bytes, 512, 2000);
 	if (ret<0) {
 		fprintf(stderr, "error: b0rken swversion read!\n");
@@ -337,3 +341,4 @@ int get_sw_version()
 	return 1;
 }
 
+#endif

src/utils.c

@@ -17,9 +17,9 @@
  */
 
 #include "main.h"
-#include <usb.h>
 #include <stdio.h>
 #include <string.h>
+#include <stdarg.h>
 #include <stdlib.h>
 
 unsigned long get_file_size(char *file)
@@ -53,3 +53,12 @@ void progressbar(unsigned long long part, unsigned long long total)
         printf("]\r");
         fflush(stdout);
 }
+
+void eprintf(const char *format, ...)
+{
+	va_list ap;
+	va_start(ap, format);
+	vfprintf(stderr, format, ap);
+	va_end(ap);
+	//fflush(stderr); // XXX CRASH?!? stdin here?!?!?
+}